Omega S profile

Ideal for:

Vertical facade installation up to a size of 60×180 cm
Solid and lightweight substrates

Advantages at a glance:

Precise joint alignment: OmegaS profile enables precise horizontal line alignment
Secure fastening: Structural positional security thanks to securing brackets (item no. 711).
Pre-assembled grids: K20 Omega profiles can be mounted in single-span structures with cantilever arms
Tool-free installation: Panels can be easily hooked in place – quickly and reliably
Flexible joint solution: Choice of open or closed horizontal joints

Typical areas of application:

Skeleton and solid wall constructions
Ventilated facades Structures with architectural line accents
Vertical installation up to overhead

Installation principle – How it works:

Install vertical support structure:
Omega profiles are installed as single-span beams with cantilever arms.

Attach OmegaS support profiles:
Serves as a support and adjustment element for horizontal joints.

Hang and secure panels:
Tool-free installation via retaining grooves – with positioning bracket

Joint solutions:
Joints can be either open or backed (support profile item no. 715).

Installation instructions

The substructure must be installed in accordance with a project-specific structural analysis. General building approval Z-10.3-844 serves as the basis for this.

The profiles of the base substructure must be installed plumb and level.
Fasten horizontal K20 omega profiles (item no. 627) to the pre-assembled vertical substructure using the fasteners supplied. Vertical spacing depending on panel length – single-span (= 1/2 of panel length) with cantilever on both sides (= 1/4 panel length)
Install support profiles in a horizontal grid (panel length + 8 mm).
Insert KeraTwin panels tightly into the structure
Position the position locking brackets on both omega profiles and fasten them in place

System components

Article 627
Omega profile blank
for mounting with joint profile K20/8
Material: AlMg3 H22 (EN AW-5754),
uncoated

Article 710
OmegaS support profile coated
Material: AlMg3 H22 (EN AW-5754)
coated black, RAL 7021

Article 711
Position locking bracket blank
Material: AlMg3 H22 (EN AW-5754)
uncoated
Box contents: 50 pieces

Article 658
Al blind rivets, bare
For fastening Omega profile and OmegaS
Nominal size: 4.8 x 10 mm
Box contents: 500 pieces
Weight: 1.3 kg/box

Article 659-01
A4 stainless steel screw, bright
Nominal size: 4.8 x 16 mm
Box contents: 500 pieces + 1 bit for mounting omega profile Weight: 2.8 kg/box

Article 688
Joint profile
Length: 1496 mm
Material: EN AW 6063 T66
black coated, RAL 7021,
RAL color coating on request

Article 689
Retaining clip for joint profile
Material: AlMg1 (EN AW 5005 A)
uncoated
Box contents: 100 pieces

Article 682R
R-clamp
Material: AlMg3 H22 (EN AW-5754),
black coated

Article 683R
R-clamp
Material: AlMg3 H22 (EN AW-5754),
black coated

Article 684R
R-clamp
Material: AlMg3 H22 (EN AW-5754),
black coated

Article 657
A2 Stainless steel screw
Head black,
RAL 7021 for fastening R-clamp

Omega profiles available for all standard grids. Other grids available on request.

Delivery lengths:
Grids 15 cm, 20 cm, 25 cm, 30 cm, 37.5 cm, 50 cm, 60 cm: 2992 mm
Grid 17.5 cm: 2967 mm · Grids 22.5 cm, 32.5 cm: 2917 mm
Grid 27.5 cm, 55 cm: 2742 mm · Grid 35 cm, 40 cm: 2792 mm
Grid 45 cm: 2692 mm

Please note: The use of silicone rubbers should generally be avoided, as silicone oils migrate and create sticky, dirt-binding surfaces. Therefore, please use only the recommended system components or consult with us regarding the planned products before processing. The usual final cleaning of the building is still required. A warranty for the KeraTwin® K20 system within the scope of general building approval no. Z-10.3-844 only applies when using the system components shown on these pages.