Clamp system

Ideal for:

 Solid and lightweight substrates
 Horizontal, vertical, and overhead installation
 Facades with variable grid sizes

Advantages at a glance:

Flexible positioning: Can be attached to any pull hole in the panel
Simple technology with system: Clamps allow quick, secure installation
Invisible fastening: the clips are not visible in the joint
Grid tolerance: slight pulling or pushing possible during alignment
Panel dimensions: possible up to 50 x 135 cm

Typical areas of application:

Concrete, masonry, steel walls, sandwich panels
Pre-assembled rear-ventilated facade – Fastening with open fastening pattern
Horizontal, vertical, bond, overhead

Installation principle – How it works:

Prepare the support profile:
Install the horizontal or vertical substructure – e.g. with aluminum profiles.

Install the panels:
The facade panels are attached to the supporting structure with clips. Positioning über existing holes in the panel – simple & präzise.

Forming joints:
Depending on the design, use joint profiles or joint tape – for clean lines and a defined look.

Horizontale Montage

Vertical mounting

Horizontal support profile (base substructure)

Edge clip K20, item no. 681

Joint tape, black, item no. 506

Wall bracket (base substructure)

Vertical support profile (base substructure)

Stainless steel blind rivet, item no. 675-01, alternatively stainless steel self-drilling screw, item no. 657

Double clip K20, item no. 680

KeraTwin^® K20 facade panel, maximum panel size 135 x 50 cm

The profile joint of the vertical support profiles must not be located behind a panel! See standard detail drawings.

Installation instructions

The substructure must be installed in accordance with a project-specific structural analysis. The Z-10.3-844 certificate of suitability serves as a basis.

The profiles of the base substructure must be installed plumb and flush.
The horizontal spacing between the support profiles (profile width ≥ 60 mm) must correspond to the length grid of the panels.
The length of the vertical profiles must be divisible by the panel format and should not exceed one floor height.
The profile end must not be located behind a panel.
The vertical joints can be covered with black joint tape (item no. 506).
The clips (item no. 680, 681, 682, 683, 684) must be fastened with at least 2 rivets (item no. 675-01) or 2 screws (item no. 657).
An extended riveting tool (25 mm) is required to work with the rivets (item no. 675-01).
An extended bit is required to work with the screws.
In the area of the clamp fastening, the joints can be closed with the joint profile (item no. 688) and one joint profile holder (item no. 689) per panel.

System components

Article 680
Double clamp K20*
Perforation: 2 x 3.3 mm Ø
Weight: 45 kg/1,000 pieces
Material: AlMg3 H22 (EN AW-5754),
coated black, RAL 7021

Article 681
Edge clip K20*
Perforation: 4 x 3.3 mm Ø
Weight: 24 kg/1,000 pieces
Material: AlMg3 H22 (EN AW-5754)
black coated, RAL 7021

Article 682
Edge clip K20, left
Perforation: 4 x 3.3 mm Ø
Weight: 24 kg/1,000 pieces
Material: AlMg3 H22 (EN AW-5754),
coated black, RAL 7021

Article 683
Edge clamp K20, right
Perforation: 4 x 3.3 mm Ø
Weight: 24 kg/1,000 pieces
Material: AlMg3 H22 (EN AW-5754)
black coated, RAL 7021

Article 684
Single clamp K20
Perforation: 2 x 3.3 mm Ø
Weight: 45 kg/1,000 pieces
Material: AlMg3 H22 (EN AW-5754),
coated black, RAL 7021

Article 657
A2 Stainless steel screw
Head black,
RAL 7021 for fastening R-clamp

Item 675-01
Stainless steel blind rivets, black
Weight: 1.05 kg/box
Nominal dimensions: 3.2 x 9.5 mm
Box contents: 500 pieces
Extended mandrel (58 mm)

Item 506
Joint tape, black
Weight: 0.5 kg/roll
Nominal dimensions: 40 mm wide, 50 m
Self-adhesive, weather-resistant

Article 688
Joint profile
Length: 1496 mm
Material: EN AW 6063 T66
black coated, RAL 7021,
RAL color coating on request

Article 689
Retaining clip for joint profile
Material: AlMg1 (EN AW 5005 A)
uncoated
Box contents: 100 pieces

Delivery of staples

Double and single staples 7 pieces/string
Edge staples 13 pieces/stranded

The use of silicone rubbers should generally be avoided, as silicone oils migrate and create sticky, dirt-binding surfaces. Therefore, please use only the recommended system components or consult with us before processing the planned products. The usual final cleaning of the building is still required. A warranty for the KeraTwin^® system within the scope of general building approval No. Z-10.3-844 only applies when using the system components shown on these pages.