Omega V-profile

Ideal for:

 Free-standing panels
Solid walls and frame constructions
 Enables a shingle look with standard panels

Advantages at a glance:

Flexible grid: Pre-assembled hole grids for easy planning
Tool-free installation: Panel mounting via retaining grooves, no special tools required
Secure and quiet: pressure spring prevents rattling
Selectable position locking: With joint profile or spacer – to match the joint width

Typical areas of application:

Concrete, masonry, sandwich panels
Standing walls and load-bearing substrates
Horizontal, free bond

Assembly principle – How it works

Assemble vertical support structure:
plumb and level (base substructure)

Attach horizontal support profiles (item no. 597-01):
at the selected hole spacing on the base substructure

Hook OmegaV profiles into the support profiles:
Secure the positionon the left and right of the hooking tabs with screws (item no. 659).

Hook in the panels:
Tool-free installation via retaining grooves on the back.

Define joints (positioning):
Optionally with joint profile or joint spacer

Befestigung mit vertikalem Systemprofil K20

Wall bracket (basic substructure)

Vertical support profile (basic substructure)

Horizontal support profile, item no. 597-01

Vertical OmegaV profile, item no. 700 (coated for open joints with spacers) or item no. 701 (uncoated for closed joints with joint profile)

Facade panel KeraTwin^® K20

Installation instructions

The substructure must be installed in accordance with a project-specific structural analysis. General building approval Z-10.3-844 serves as the basis for this.

The profiles of the base substructure must be installed plumb and level.
Attach the horizontal support rail (item no. 597-01) to the base substructure using fasteners in accordance with the structural calculations.
Hang the OmegaV profiles exactly at the horizontal grid spacing.
The horizontal spacing of the rails must correspond to the longitudinal grid of the panels.
Secure the OmegaV profiles in place on the left and right of the mounting lugs with screws (item no. 659).
For open vertical joints, insert one spacer (item no. 645) per panel into a central pull hole in the panel.
For closed vertical joints, use the OmegaV joint profile (item no. 707).

System components

Article 597-01
Horizontal mounting rail, perforated
Standard length: 2995 mm
Nominal dimension: 05/90 x 25 mm
Material: EN AW 6063 T66 uncoated

Article 700
OmegaV coated,
for mounting with joint spacer K20/8
Material: AlMg3 H22 (EN AW-5754)
black coated RAL 7021

Article 701
OmegaV blank
Material: AlMg3 H22 (EN AW-5754)
uncoated for mounting with joint profile OmegaV K20/8

Article 705
OmegaV outside corner blank
Material: AlMg3 H22 (EN AW-5754)
uncoated for mounting miter plates and outside corner profiles

Article 707
Joint profile OmegaV K20/8
Material: AlMg3 H22 (EN AW-5754)
black coated RAL 7021,
RAL color coating on request

Article 712
Joint extension profile OmegaV K20/8
Material: AlMg3 H22 (EN AW-5754)
black coated RAL 7021,
RAL color coating on request

Article 645
Joint spacer K20/8
Material: AlMg3 H22 (EN AW-5754),
Box contents: 250 pieces,
Weight: 0.5 kg/box,
coated black RAL 7021

Article 658
Al blind rivets, bare
for mounting system profile
Nominal size: 4.8 x 10 mm,
Box contents: 500 pieces,
Weight: 1.3 kg/box

Article 659-01
A4 stainless steel screw, bright
Nominal size: 4.8 x 16 mm
Box contents: 500 pieces + 1 bit for mounting omega profile Weight: 2.8 kg/box

Article 650 / 652 / 654
External corner profile square / sword / negative
(EN AW-5754),
black coated,
RAL color coating on request

Article 682R
R-clamp
Material: AlMg3 H22 (EN AW-5754),
black coated

Article 683R
R-clamp
Material: AlMg3 H22 (EN AW-5754),
black coated

Article 684R
R-clamp
Material: AlMg3 H22 (EN AW-5754),
black coated

Article 657
A2 Stainless steel screw
Head black,
RAL 7021 for fastening R-clamp

OmegaV profiles and joint profiles are available for all standard grids from 20 cm. Other grids are available on request.

Please note: The use of silicone rubbers should generally be avoided, as silicone oils migrate and create sticky, dirt-binding surfaces. Therefore, please use only the recommended system components or consult with us regarding the planned products before processing. The usual final cleaning of the building is still required. A warranty for the KeraTwin® K20 system within the scope of general building approval no. Z-10.3-844 only applies when using the system components shown on these pages.